Repeat this step for the tail light on the other side using another standard Bit Light. Ensure the cable from the LED is facing toward the middle so that we can hide it behind the back piece we removed earlier. Secure the LED in place by reconnecting the transparent red piece over the top of it. Take a standard Bit light(non flashing) and place it over the top of the red stud on the side of the car ensuring the LED component part is facing the correct way up. Remove the transparent red cone pieces from each side of the car. The back section should remove in one piece. Turn the car to the back and remove the back window and white back section of the car. Reconnect this section back to the side of the car ensuring the cable from the LED is on the inside facing the car.ĩ.) Take the cable from the LED we just installed and the 2 cables from the front right lights and hide them in between studs up the right side of the car by reconnecting the grey triangular plates over the top of them.ġ0.) We will now install 2 LEDs to the tail lights. Ensure the LED component part is facing down or inward Secure this into place by connecting another transparent blue plate (which we have provided) over the top. Take another standard Bit Light (non flashing) and install it with the LED component part facing down (as it wont connect with it facing up). To do this, remove this section at the grey stud with clip. Reconnect the front middle section with the grill and number plate attached.Ħ.) Before reconnecting the white Lego pieces which make up the front bonnet, ensure that the cables from the LEDs are laid in between the studs of the Lego plates underneath as per below example images.ħ.) Hide 2 cables from the lights on the left side of the car (looking from the front) up the left side by laying them in between the white studs and then reconnecting the grey triangular plates over the top of them.Ĩ.) Before we hide the 2 cables from the right we will first install an LED to the blue light at the right side window. Reconnect the light pieces back to the 2 Lego 2×4 plates ensuring that the cables from the LEDs are facing upward and then reconnect the plates back to the front of the car. Install the remaining LEDs to all front headlights (2 on each side) using the above process so that we have a total of 4 standard Bit lights installed. Secure the LED in place by connecting the transparent Lego plate over the top. Take 1 standard Bit Light (non flashing) and place it on top of the stud of the grey round plate ensuring the LED component part is facing the correct way up. To do this, remove the following pieces from the front of the car.Ĭontinue to remove the following pieces which make up the windscreen, side windows, and grey triangular tiles from the sides of the car.Ĥ.) Remove the front section with the grill and number plate attached, followed by the 2 Lego 2×4 plates with light pieces attached.ĥ.) Remove the 2 grey round pieces as well as the transparent round pieces connected to them. You can either place them directly on top of LEGO® studs or in between.ġ.) Let’s start by removing the roof of the car.Ģ.) We will be installing lights to the headlights first. When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). Installing Bit Lights under LEGO® bricks and plates. WARNING: Incorrectly inserting the connector can result in bent pins inside the port or possible overheating of the expansion board when connected. If a plug won’t fit easily into a port connector, do not force it. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. Take extra care when inserting connectors to ports of Expansion Boards. Connecting cable connectors to Expansion Boards Do NOT forcefully join LEGO® together around cables instead ensure they are laying comfortably in between each stud.ĬAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light. Important things to note: Laying cables in between and underneath bricksĬables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. 1x Lego 1×1 round plate (transparent blue).1x Flat Battery Pack (requires 2x CR2032 Batteries).This user guide is also available to download in PDF format here. If you run into any issues, please refer to the online troubleshooting guide. To ensure a trouble-free installation of your light kit, please read and follow each step carefully. You purchase this kit on our official website. The following page is instructions for the Light My Bricks LEGO Ghostbusters Ecto-1 (21108) LED light kit.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |